How Does Electrical Insulation Work?

By | September 2, 2026

An insulator has almost no charge carriers free to move. Apply a voltage and the charges inside it shift slightly but stay bound, so current flow is tiny compared with a conductor. That holds until the electric field gets strong enough, or the material weak enough, to tear carriers loose. Then you get breakdown.

That is the mechanism. But it only explains part of what happens in real equipment, because insulation does not fail as a material — it fails as a system, in a specific geometry, at a specific temperature, after a specific service history.

So it is worth looking at three levels.

Level 1 — What the material is doing

Conductors have electrons that are free to move. In copper, outer-shell electrons are not tied to any one atom. Apply a small field and they drift immediately. That drift is the current.

Insulators do not. Their electrons are tightly bound. In band-structure terms, the gap between the filled valence band and the empty conduction band is large — typically several electronvolts, well above the roughly 1 eV region of semiconductors. At normal temperatures and normal fields, very few electrons get enough energy to cross it.

Copper has a resistivity around 10⁻⁸ Ω·m, while common solid insulating materials can range roughly from 10¹² to 10¹⁶ Ω·m, depending strongly on material, purity, moisture and temperature. That enormous difference is why insulation carries only a small leakage current under normal conditions.

But something does happen inside the material

Applying voltage to insulation is not a null event. Three things occur, on different timescales:

  1. Capacitive charging. The insulation is a dielectric between two conductors, so it charges like a capacitor. This current is large at first and decays quickly.
  2. Polarisation and absorption. Charges inside the material shift and dipoles rotate to line up with the field. This does not move charge across the insulation, but it does draw current while it settles, and it can take minutes in large machines and cables.
  3. Conduction. A small steady current that actually crosses the insulation. This is leakage.

That sequence is the basis of insulation resistance testing. Read too early and you are measuring charging current, not insulation condition. Read after the transients settle and you are closer to what you care about.

The increase in insulation resistance with time reflects polarization and absorption behaviour. The polarization index, normally calculated as the ratio of the 10-minute resistance to the 1-minute resistance, uses this behaviour as an indicator of insulation condition.

Level 2 — What the geometry is doing

Here is where intuition often goes wrong. Insulation breakdown often starts where the electric field is highest, which may not be where the bulk material is weakest. Material defects still matter — voids, contaminants and inclusions can themselves raise local field stress.

Electric field strength, or stress, is what breaks insulation, measured in kV/mm. And field strength depends on shape as much as on voltage:

  • Sharp edges concentrate field. A burr on a lug, a wire strand standing proud, a sharp corner on a busbar support — the field crowds at small radii. Local stress can be substantially higher than the average stress across the gap.
  • Thin sections concentrate field. The same voltage across a thinner layer means higher stress.
  • Series layers split the field unevenly. This is the important one.

Why a void is dangerous

When two dielectrics sit in series in the same field, the stress divides in inverse proportion to their permittivity. The lower-permittivity material takes the higher share.

Approximate relative permittivity values look like this:

MaterialRelative permittivity (approx.)
Air / gas-filled void~1
Mineral insulating oil~2.2
XLPE~2.3
EPR~2.5 to 3.5
Oil-impregnated paper~3.5
Epoxy resin~3.5 to 5

Now put an air-filled void inside XLPE. The void has the lowest permittivity in the assembly, so it takes the highest field. It also has by far the lowest dielectric strength. Higher stress in the weakest material — that is the worst possible combination, and it is why voids matter more than their size suggests.

If the field in the void exceeds the discharge inception level, you get partial discharge: a small, repetitive breakdown inside the void that never bridges the full insulation. Over time, repeated discharge can cause chemical and physical degradation around the void and initiate electrical treeing, in which branched damage channels progressively extend through the insulation.

Whether a void discharges at all depends on more than its diameter. Gas breakdown depends on the product of pressure and gap length, not the gap alone, so small voids can be harder to ignite. Good manufacturing practice aims to minimise voids and other defects, because their size, internal pressure and location determine whether partial discharge can occur.

Level 3 — What the heat is doing

Insulation is never a perfect capacitor. Some of the energy going into it each cycle turns into heat, from polarisation losses and from conduction.

This is what dissipation factor, tan δ, describes: for the usual small-loss case, the ratio of the resistive component of current to the capacitive component. In healthy insulation it is small. As insulation deteriorates through mechanisms such as moisture ingress, ageing or contamination, dielectric losses can increase and tan δ can rise. That is why tan δ measurement is a useful condition indicator on transformers, bushings and cables — it watches the loss mechanism directly.

Losses matter for two reasons.

They age the material. Thermal ageing is a chemical process. Higher temperature means faster degradation, following an Arrhenius-type behaviour where life falls off steeply as temperature rises. The familiar rule of thumb about a 10 °C rise halving life comes from this, though it is an approximation and the real coefficient depends on the material system.

They can run away. Losses generate heat. Heat raises conductivity and increases losses. If heat generation exceeds heat dissipation, the loop feeds itself. Thermal runaway is a genuine breakdown mode, and it matters particularly in thick insulation or poorly cooled structures, where heat generated inside the dielectric is difficult to remove.

So the three levels connect. Material properties set the baseline. Geometry decides where the stress lands. Heat decides how fast everything degrades.

The ways insulation stops working

MechanismWhat happensTypical timescale
Electronic breakdownVery high field produces rapid carrier multiplication and breakdownImmediate
Thermal breakdownHeat generation exceeds dissipation; runawayMinutes to hours
Partial discharge and erosionVoid discharges degrade the material from insideMonths to years
Surface trackingContaminated damp surface carbonises into a conducting pathWeeks to years
Moisture ingressLeakage rises, dielectric strength fallsMonths to years
Mechanical damageCuts, crushing, vibration abrasion, thermal cyclingAny

The first is dominated by the intrinsic electrical strength of the material. The others depend strongly on the insulation system, its geometry, environment and service history — which is the practical reason routine testing exists.

The same insulation can fail in more than one way

These mechanisms do not queue up politely. A single insulation system can experience several at once. Moisture raises leakage current, heat accelerates ageing, and a void produces local partial discharge — and those processes reinforce each other rather than running independently. Moisture lowers the discharge inception level. Discharge produces heat and by-products. Heat drives further chemical change.

That is why a single test result should never be read in isolation. A useful insulation assessment combines the test method with temperature, equipment type, physical condition, service history, and previous measurements on the same asset.

What this means for testing

Each mechanism leaves a different signature, and no single test catches all of them:

  • Insulation resistance and polarization index can reveal changes associated with moisture, contamination and insulation condition, when interpreted alongside temperature, equipment type and test history.
  • Tan δ / power factor tracks bulk dielectric loss, so it responds to general ageing and moisture across the volume.
  • Partial discharge measurement can detect localised discharge activity that may have little effect on insulation resistance or tan δ in the early stages.
  • Withstand testing confirms the insulation holds a defined stress, which resistance measurements cannot tell you.

A machine can pass an insulation resistance test comfortably while carrying internal discharge activity that will fail it later. That is not a contradiction. The tests look at different levels of the same system.

FAQ

Does any current flow through insulation?

Yes, a small amount. After capacitive and absorption currents settle, a steady leakage current remains. Its magnitude depends strongly on the insulation system, its temperature, and the test conditions. It is never exactly zero.

Why does moisture affect insulation so much?

Moisture can introduce mobile ions, increase conductivity and surface leakage, alter the electric-field distribution, and reduce dielectric strength. It also enables tracking on surfaces and is associated with water treeing in polymeric cable insulation.

What is dielectric strength, exactly?

The field strength a material can withstand before breakdown, in kV/mm. It is determined under defined test conditions, and the value depends heavily on thickness, electrode shape, waveform and duration. Treat published figures as comparative rather than as a design limit.

Why does thicker insulation not simply mean safer?

More thickness lowers the average electric stress for a given voltage, but it can also make heat removal more difficult, increasing thermal stress in some designs. It also gives more volume in which manufacturing defects can hide.

Is breakdown always permanent?

In solids, generally yes — a puncture leaves a damaged, often carbonised channel. In gases such as air, breakdown can be self-restoring once the discharge path clears. Some liquid insulation can also recover dielectric strength after a transient breakdown, but that depends strongly on contamination, moisture, decomposition products and the condition of the liquid.

If a material has high resistance, does it have high dielectric strength?

Not necessarily. Resistance governs how much current leaks at a given voltage. Dielectric strength governs the field at which the structure fails. They are related but distinct properties, and a material can perform well on one and less well on the other.

Author: Zakaria El Intissar

Zakaria El Intissar is an automation and industrial computing engineer with 12+ years of experience in power system automation, electrical protection, and SCADA systems. He founded InsulationTesting.com to share practical, field-tested guides on insulation resistance testing, equipment, and industry standards. His writing is used by electricians and maintenance engineers worldwide. Based in Morocco.

Leave a Reply

Your email address will not be published. Required fields are marked *