What Is the Purpose of Electrical Insulation?

By | September 2, 2026

Take a 400 V motor feeder and strip the cable back to bare copper. Nothing dramatic happens while the conductors stay apart. The air between them is doing the insulating, and dry air under normal atmospheric conditions holds off roughly 3 kV per millimetre. Treat that as a rule of thumb, not a fixed value — it shifts with pressure, humidity, gap length and electrode shape.

Now let the conductors sag together, or let a film of salty dust settle across the terminal block. Current stops going where you sent it and goes where the path is easiest. That is the whole problem in one sentence.

Insulation is not a passive wrapper. It controls where current can and cannot flow, by putting a high-resistance barrier between conductors, and between live parts and earth.

Job 1: Control the current path

The first purpose is the obvious one. A conductor carries current from A to B. Insulation makes sure it arrives at B instead of finding its way into the frame, the earth, the adjacent phase, or your hand.

Good insulating material has resistivity many orders of magnitude above copper. Nothing is a perfect barrier, though. Apply DC test voltage to an insulation system and you first see capacitive charging current, then absorption current as the material polarises. Once those transients settle, what remains is mainly leakage current. That settled value is what an insulation resistance reading is really about. When leakage climbs over time, the barrier is weakening.

Job 2: Hold off the voltage stress

Limiting current and withstanding voltage are not the same requirement. A material can have very high resistance and still puncture when you push enough volts across it.

Voltage stress is what matters here, measured in kV per mm. Squeeze the same voltage into a thinner gap and the stress goes up. That is why insulation thickness is tied to system voltage, and why the sharp edge of a badly dressed lug is a problem — field lines crowd at sharp points, local stress spikes, and breakdown can start there long before the bulk material is anywhere near its limit.

Three things make this job harder over time:

  • Voids. A gas-filled void inside solid insulation has lower breakdown strength than the material around it, and the field across it is often higher. If the local field exceeds the inception level, the void becomes a partial discharge site. A void does not guarantee PD, but it creates the conditions for it, and once PD starts it erodes the surrounding material.
  • Moisture. Water raises leakage current and lowers dielectric strength. It is one of the most common reasons a machine fails a routine test.
  • Contamination. Carbon, salt and metal dust give the current a head start.

Job 3: Handle the heat

This is the purpose people forget. Insulation has to survive the temperature of the conductor it is wrapped around, for twenty or thirty years, without going brittle.

Thermal classes under IEC 60085 assign a maximum continuous-use temperature to the insulation system:

ClassRated temperature
A105 °C
E120 °C
B130 °C
F155 °C
H180 °C
N200 °C

Read that table carefully. The class is the temperature the system is rated for in continuous service, judged against the relevant standard. It is not a threshold where the material suddenly fails. Running above the rating does not cause instant breakdown — it accelerates ageing.

There is a well-known empirical approximation that every extra 10 °C roughly halves remaining life. Useful for a quick mental check, but it is an approximation, and the real rate depends on the material system and the applicable loading guide. The practical point stands either way: a Class F motor run continuously at Class H temperatures still turns for years. It just gets a fraction of the service life you paid for, and the failure lands in the middle of a production run instead of during a planned outage.

Heat and voltage stress also work together. Hot insulation is weaker insulation.

Job 4: Resist tracking across surfaces

Breakdown through the bulk of a material is one failure mode. Creeping along its surface is another, and it needs a different defence.

When a contaminated, damp surface carries small leakage currents, dry-band arcs form. Each arc can carbonise a little of the surface. Carbon conducts. So the next arc has a shorter gap to bridge, and the conductive path grows until it walks the full distance between conductors. This is tracking, and it is a slow, self-feeding process.

Resistance to it is graded by comparative tracking index, determined with the IEC 60112 test. Materials fall into groups defined by CTI range:

  • Group I — CTI 600 and above
  • Group II — 400 up to 600
  • Group IIIa — 175 up to 400
  • Group IIIb — 100 up to 175

Outdoor materials get a harder test. IEC 60587 is not a CTI test — it evaluates tracking and erosion under sustained electrical and environmental stress on an inclined plane, which is closer to what a polymeric insulator sees in service.

This is also why insulation design specifies two distances. Clearance is the shortest path through air. Creepage is the shortest path along the surface. Creepage is often the longer of the two, especially where pollution demands an extended surface path, though the two are separate geometric paths and can be close in value. Ribs and grooves in a terminal block are not styling — they lengthen the creepage path without making the part bigger.

Job 5: Protect people

Everything above is about protecting the equipment. This one is about whoever opens the panel.

Basic insulation is the first layer. Because any single layer can be damaged, protective measures add more: supplementary insulation, double or reinforced insulation, plus earthing and residual current protection. The design intent is that a single insulation fault does not normally expose a person to a dangerous touch voltage.

Mechanical protection belongs in the same discussion, but keep the roles separate. In a cable, the core insulation provides the dielectric function. The outer sheath or jacket is there for mechanical and environmental protection — abrasion, crushing, UV, oil, rodents. A jacket that survives the pull through a conduit is doing essential work, but it is not the part holding off the voltage.

Why the purpose defines the test

Each job maps to a different test, which is why insulation testing is never one measurement:

PurposeWhat you testTypical reference
Control current pathsInsulation resistance, polarization indexIEEE 43 for rotating machines
Withstand voltageApplied and induced voltage withstandIEC 60076-3 for transformers
Detect PD activityPartial discharge measurementIEC 60270
Resist trackingCTI; tracking and erosion for outdoor materialsIEC 60112, IEC 60587
Dielectric strength of insulating oilBreakdown voltageIEC 60156
Condition of oil in serviceMoisture, acidity, and related oil-condition checksIEC 60422

A megohmmeter tells you about resistance under the applied test voltage. It tells you very little about whether the insulation will survive an impulse. Different purposes, different tests.

One practical point on measurement: insulation resistance is strongly temperature dependent. A reading taken at 20 °C and one taken at 55 °C on the same healthy machine can differ by several times, and in some cases by an order of magnitude or more. Correct readings to a common reference temperature before comparing them against history. Otherwise you will chase a fault that only exists in the arithmetic.

The short version for the job site

Insulation exists so that electrical energy stays inside the system and everything outside it stays safe. It does that by controlling current paths, withstanding voltage, tolerating heat, resisting surface tracking, and working alongside mechanical protection.

It is also the part of the installation most sensitive to the conditions it lives in. Conductors and steelwork degrade too — corrosion, fatigue, thermal cycling, mechanical damage — but insulation is the element most exposed to combined thermal, moisture and electrical stress, and it ages quietly from day one. That is why it gets tested on a schedule and the busbar does not.

FAQ

Is insulation the same as a dielectric?

Almost, but the emphasis differs. Insulation describes the function of limiting current flow. Dielectric describes the material property of storing energy in an electric field. The same epoxy is both. You use the word “dielectric” when you care about capacitance, permittivity, and dissipation factor.

Can air be insulation?

Yes, and it is used deliberately in air-insulated switchgear and overhead lines. Its advantage is that it is self-restoring — after a flashover, the air recovers. Its disadvantages are relatively low dielectric strength and sensitivity to humidity, pollution, and altitude.

Why does insulation resistance drop when the equipment is warm?

Higher temperature increases charge carrier mobility in the material and drives moisture activity, so leakage current rises and measured resistance falls. This is expected behaviour, not automatically a fault. Compare readings only after correcting to a reference temperature.

Does thicker insulation always mean better?

No. More thickness raises the withstand level but also impedes heat removal, which accelerates thermal ageing. It adds size and cost too. Insulation design balances electrical stress, thermal performance, and mechanical strength.

What usually damages insulation first?

Common causes include moisture, thermal ageing and overload, electrical stress and partial discharge, surface contamination, vibration, and mechanical damage during installation or maintenance. Which one dominates depends on the equipment and the environment. Most of them are gradual, and most show up in routine testing before breakdown — which is the argument for periodic testing rather than run-to-failure.

Is a passed insulation resistance test enough to return equipment to service?

It depends on the equipment, the voltage level, and the maintenance procedure you are working to. A good IR value indicates acceptable insulation resistance under the conditions of that test. It does not prove the insulation will withstand rated voltage or an impulse, and it does not rule out internal defects. For MV and HV equipment, the test program in the relevant standard or the owner’s procedure decides whether withstand or PD testing is also required.

Author: Zakaria El Intissar

Zakaria El Intissar is an automation and industrial computing engineer with 12+ years of experience in power system automation, electrical protection, and SCADA systems. He founded InsulationTesting.com to share practical, field-tested guides on insulation resistance testing, equipment, and industry standards. His writing is used by electricians and maintenance engineers worldwide. Based in Morocco.

Leave a Reply

Your email address will not be published. Required fields are marked *